![what is indicated by the m in the cisco ios image name c1900-universalk9-mz.spa.153-3.m.bin? what is indicated by the m in the cisco ios image name c1900-universalk9-mz.spa.153-3.m.bin?](https://i0.wp.com/itexam24.com/wp-content/uploads/2019/05/i212355v1n1_Question2011.png)
- What is indicated by the m in the cisco ios image name c1900 universalk9 mz.spa.153 3.m.bin? serial#
What is used as the default event logging destination for Cisco routers and switches?ġ3. The time on the router when the show logging command was issuedġ2. The time passed since the interfaces have been up The time when the syslog message was issued* The time passed since the syslog server has been started Synchronizes the system clock with the time source with IP address 10.1.1.1*ĬCNA 2 v6.0 Chapter 10 q11 What does the number 17:46:26.143 represent? Identifies the server on which to store backup configurationsĮnsures that all logging will have a time stamp associated with it What impact does this command have?ĭetermines which server to send system log files to
![what is indicated by the m in the cisco ios image name c1900-universalk9-mz.spa.153-3.m.bin? what is indicated by the m in the cisco ios image name c1900-universalk9-mz.spa.153-3.m.bin?](https://www.coursehero.com/thumb/1c/3e/1c3e6ee73df8d675fbf85c020372cc3100d398fc_180.jpg)
The command ntp server 10.1.1.1 is issued on a router. NTP servers control the mean time between failures (MTBF) for key network devices.Ħ. NTP servers ensure an accurate time stamp on logging and debugging information.* NTP servers at stratum 1 are directly connected to an authoritative time source.* There can only be one NTP server on an enterprise network.Īll NTP servers synchronize directly to a stratum 1 time source. Which two statements are true about NTP servers in an enterprise network? (Choose two.) Router R2 is the master, and R1 is the client.ĥ. Router R1 is the master, and R2 is the client.* Which two pieces of information can be obtained from the partial output of the show ntp associations detail command on R2? (Choose two.)īoth routers are configured to use NTPv2. One router is configured as the NTP master, and the other is an NTP client.
What is indicated by the m in the cisco ios image name c1900 universalk9 mz.spa.153 3.m.bin? serial#
To display routing table and other information about directly connected Cisco devicesĬCNA 2 v6.0 Chapter 10 q4 Routers R1 and R2 are connected via a serial link. To display line status and other information about directly connected Cisco devices To display router ID and other information about OSPF neighbors To display device ID and other information about directly connected Cisco devices* Why would a network administrator issue the show cdp neigbors command on a router? To disable CDP globally, the no cdp enable command in interface configuration mode must be used.ĬDP can be disabled globally or on a specific interface.*īecause it runs at the data link layer, the CDP protocol can only be implemented in switches.ģ. The show cdp neighbor detail command will reveal the IP address of a neighbor only if there is Layer 3 connectivity. Which statement is true about CDP on a Cisco device? The network administrator wants to determine if connectivity can be established from a non-directly connected network.Ģ. The network administrator wants to verify the IP address configured on router R2. The network administrator wants to verify Layer 2 connectivity.* The network administrator suspects a virus because the ping command did not work. Why would the network administrator issue this command if the ping failed between the two routers? The network administrator then proceeds to issue the show cdp neighbors command. A ping fails when performed from router R1 to directly connected router R2. Cisco CCNA 2 v6.0 Chapter 10 Exam Answers 2018 Score 100% 1.